Corrugated Plastic Case Suppliers introduces the requirements for the use of hollow plates:

1. Cleaning of the hollow board: It is necessary to clean it with warm water below 60℃. Use a neutral scouring agent when cleaning, do not allow to use of a scouring agent that has a corrosive effect on the endurance board. Begged to use a thin cloth or sponge dipped in neutralizing liquid to clean it secretly.

2. It is forbidden to use old coarse cloth, soft brush, mop, and other hard and sharp special tools for cleaning. The unsuitable cleaning agent is an alkaline solution, which will attack the surface. It is forbidden to use esters, macrolides, benzene homologs, and all chemical substances that can melt or solubilize polycarbonate.

3. Storage and transportation of hollow boards: Keep them indoors, and never allow direct sunlight or rain; stack them by hand, and the stack height should not exceed two meters. No heavy objects shall be placed on the boards, and no hard objects shall be placed between the boards. The storage room must be clean, dry, and prevent dust from intruding. No other chemical substances should be stored indoors at the same time.

4. During storage, do not damage or remove the maintenance film. During transportation, it must be placed flat on a clean flat pallet with an area larger than the board. If necessary, it should be properly tied to prevent vibration and sliding. Pay attention to the maintenance of the board edge to prevent damage and the double-sided maintenance film to keep it intact.

5. Precautions for using hollow board: When installing, the construction organizer must clarify the text printed on the maintenance film and understand the precautions clearly.

6. Do not remove the maintenance film in front of the equipment. Only lift the maintenance film up and down 50 mm along the borderline of the board. Remove the maintenance film immediately after the end of the equipment. If it is necessary to maintain the surface again, remove the film first, and then cover the maintenance film again. The viscous chemical substance of the sealing material solves the PC sun panel without damage.

www.yfcorrugatedplastic.com

Regardless of whether it is a hollow board or other products, the service life will be different due to different storage environments and different methods during use. Therefore, if we want to make the hollow board products to be used for a long time, we must pay special attention to some methods of use when using them. The hollow board is damaged and corroded due to improper operation or improper maintenance. For the hollow board, its appearance is a moderately hard and soft packaging material. Even though it has barrier materials, due to long-term storage and the impact of its stacking location, this part of the structure has become a severely damaged area of ​​corrosion. Below, Corrugated Plastic Sheet Suppliers introduces how to use hollow sheets correctly:

1. Do not use too much force or exceed the load-bearing range of the hollow board. Do not throw the hollow board product on the ground forcibly or drag it on the ground during use; different items can be customized with different weight-bearing hollow boards, which can greatly extend its service life.

2. Deal with the medium that can cause corrosion problems and eliminate the harmful medium. These methods are relatively simple and the effect is very good.

3. Avoid exposure to the sun or rain. Although the hollow board can be waterproof and moisture-proof, it is also a degree of attention. Do not throw the hollow board product outdoors for a long time in the sun or rain, which will greatly shorten the service life.

4. Chemical protection law. The appearance of the hollow plate is used as the cathode of the damaged object to prevent it from being corroded. Therefore, it is also called the cathode protection method. This method is generally used less.

5. Chemical prevention law. This method is to uses the principle of the galvanic battery to realize the protection of the appearance of the hollow board. As long as the factors that can cause chemical corrosion are eliminated, the goal can be achieved. This is one of the common maintenance methods for manufacturers.

Through the above introduction, Corrugated Plastic Container Manufacturers hopes that you can simply refer to the content of this article in future use.
https://www.yfcorrugatedplastic.com/

What is the calcium plastic box introduced by the Corrugated Plastic Sheet Supplier ? The calcium plastic box is composed of polyethylene or polypropylene raw materials and calcium carbonate powder, and then add some lubricants zinc stearate, barium stearate, antioxidant CA and DLTP fillers, and finally through high pressure and high temperature mixing and rolling Compressed, high strength, adjustable hardness, good compression resistance, the reasons are as follows:

Determined by the rigidity of polypropylene and polyethylene. Both are crystalline resins, and the rigidity of the resin is generally related to the degree of crystallinity. The higher the resin density, the higher the rigidity and the hardness of the molded product can be randomly adjusted during processing.

The chemical properties of polypropylene and polyethylene are stable. They can resist all organic chemicals and solvents, have good acid resistance, alkali resistance, and excellent corrosion resistance. Coupled with the water resistance and moisture resistance of plastics, they are not affected by the external environment at all.

Various stabilizers can be added during the production process of calcium plastic board to strengthen and prevent aging. The formula for adding stabilizers can be divided into two types: formulas for food containers and industrial formulas used under harsh conditions at high temperatures. Manufacturers can make adjustments according to their needs during production, including product rigidity, viscosity, heat resistance, impact resistance, and transparency, Shrinkage, degree of warpage, etc.

Through the above introduction,Corrugated Plastic Container Manufacturers hopes that you can simply refer to the content of this article in future use.

https://www.yfcorrugatedplastic.com/

Calcium plastic corrugated boxes are widely used in transportation packaging. The reason why calcium plastic corrugated boxes are so popular in many industries, below, Corrugated Plastic Sheet Factory introduces the advantages of calcium plastic corrugated boxes.

Because the calcium plastic corrugated box has a special structure, its cushioning performance is very good, and the cardboard structure is empty, so the calcium plastic corrugated box is very shock-resistant, and can effectively prevent product collisions during transportation. Moreover, there are many raw materials for the production of calcium plastic corrugated boxes, so the production cost is very low, such as wood, bamboo and reeds can be made into corrugated paper.

We know that the structure of the calcium plastic corrugated box is hollow, and it can be made into a large volume with a few materials, so it is light and strong, not as heavy as a wooden box of the same volume. Due to the small volume of the calcium plastic corrugated box, it can be folded during transportation and can be opened again during use, which does not occupy transportation space and improves transportation efficiency.

The use of calcium-plastic corrugated boxes for packaging goods facilitates the automation of commodity packaging, greatly reduces the workload of packaging, and also saves a certain amount of labor costs, and is more convenient for automated production. Therefore, the current assembly line can produce corrugated boxes in large quantities. Calcium plastic corrugated boxes can be used to pack any goods, and add moisture-proof and shock-resistant materials. It can also pack a wider variety of products. The use of moisture-proof calcium plastic corrugated boxes can also be used for packaging fruits and vegetables; with plastic film covering, it can also easily package moisture-absorbing items; plastic film sleeves can be used to seal the packaging in the box so that liquid and semi-liquid items can be packaged.

In printing, the calcium-plastic corrugated box has excellent ink absorption capacity, which is very conducive to the drawing of advertisements and reduces the consumption of metal. Compared with wooden boxes, the manufacturing cost of corrugated boxes is only a small part of it, and it is very environmentally friendly. Corrugated boxes can be used many times, no pollution to the environment is a very cost-effective packaging material.

Through the above introduction, China Corrugated Plastic Container Wholesaler hopes that you can simply refer to the content of this article in future use.

The hollow board turnover box is a large number of boxes used for the turnover loading, packaging, storage, and transportation of electronic equipment and products. It has anti-bending, anti-aging, tensile strength, tensile strength, compression resistance, tear resistance, and high-temperature resistance. Next, Corrugated Plastic Sheet Factory will introduce the styles of hollow board turnover boxes?

1.From the appearance point of view, it can be divided into standard, diagonal, and dislocation styles. Standard boxes are regular square and rectangular styles. The diagonal box can be customized according to customer requirements, and the side can be inclined. Insert the PE bag to insert the label for easy classification and identification.

2.According to the function of the hollow board turnover box, it can be divided into anti-static and non-anti-static. The anti-static box can be used for the turnover and storage of a special anti-static dust-free workshop, and can also be made into a toolbox.

3.According to the different lids, it can be divided into a flip lid and a flat lid. The flip and flat cover can be designed according to customer needs, and the seal can be designed with Velcro.

4.According to performance, with and without cover. A box with a lid will block dust, and a box without a lid is very convenient to take things.

Through the above introduction, China Corrugated Plastic Container Wholesaler hopes that you can simply refer to the content of this article in future use.

Plastic logistics turnover boxes are used more in the logistics industry. Especially with the development of online shopping, the role of logistics has become more and more important, and the use of logistics transportation has been increasingly recognized by the majority of users, so the demand is also increasing. Below, Corrugated Plastic Sheet Factory introduces how to use the turnover box:

Plastic logistics turnover box, as a product similar to the outer packaging, is very important. We must choose the right plastic box when we buy it. If you buy a small one, you can’t put things in. If you buy a large one, the product is in During transportation and handling, it will sway from side to side and collide with the box. Once the product is damaged, the gain will not be worth the loss. Therefore, we must try our best to choose the right plastic logistics turnover box.

Secondly, the use frequency of plastic logistics turnover boxes is relatively high, and the use time is relatively long, so we must choose those with strong load-bearing capacity, wear resistance, and non-deformation when purchasing plastic images. Especially when placing some heavier products, the load-bearing capacity of the turnover box is very important. Plastic turnover boxes generally have relatively fixed specifications, but the weight of the placed goods is sometimes relatively high. Moreover, it is very likely to have a relatively sharp water chestnut, so choosing a solid and wear-resistant plastic turnover box can increase the service life of the box.

When selecting, check for peculiar smell. If the plastic products are not handled properly, it is easy to leave peculiar smell. The peculiar smell is a manifestation of plastic products not meeting production standards. Generally speaking, some inferior plastic products will have peculiar smell. Since the turnover box is likely to be used in the food processing industry, it is very important to ensure that the product has no toxic side effects and no peculiar smell.

Secondly, when we choose plastic logistics turnover boxes, we try our best to choose new materials. We want to return to the new materials of plastic turnover boxes with better quality, bright colors, no peculiar smell, and longer wear resistance. Some plastic products of poor quality will change in winter and hot summer. Therefore, when choosing, we must choose those products that have passed the production technology and have high-quality materials.


Through the above introduction, China Corrugated Plastic Container Wholesaler hopes that you can simply refer to the content of this article in future use.

With the development of science and technology and the progress of society, our living standards are constantly improving. At the same time, more and more wastes are generated. So it is very important to do a good job in garbage classification and garbage disposal. To the trash can. Plastic trash cans are a relatively common type of trash can, and they are mostly used for sanitation work. There are many specifications of sanitation plastic trash cans, usually 50L, 100L, 120L, 240L, etc., among which 120L and 240L are frequently used. Generally, sanitation plastic trash cans can be equipped with sanitation garbage compression trucks, so they must require high strength. Good quality. Next, Corrugated Plastic Sheet Factory will introduce to you the knowledge of sanitation plastic trash cans.

1. The manufacturing process principle of sanitation plastic trash cans: It is made of high-density polyethylene (HDPE) injection molding, which has good heat resistance and cold resistance, acid resistance, alkali resistance, corrosion resistance, strong weather resistance, good chemical stability, and It has high rigidity and toughness, good mechanical strength, anti-aging and long service life. The lid and body of the plastic trash can are formed by injection molding at one time, and the overall structure is strong. This structure has no gaps, which can reduce spillage and leakage when cleaning garbage and avoid secondary pollution of the environment by garbage leakage.

2. The difference in raw materials: Generally speaking, if the same specifications of sanitation plastic trash cans are used, the heavier the better, but this is also a more deceptive trap. Untrustworthy plastic trash can manufacturers will Adding recycled materials and other materials that can increase the weight of the raw materials will cause the plastic trash can to decrease in toughness and easily break, and the service life of the plastic trash can is greatly shortened.

Through the above introduction,China Corrugated Plastic Container Wholesaler hopes that you can simply refer to the content of this article in future use.

Corrugated Plastic Sheet Factory Introduction What is the production process of Corrugated Plastic Containe?

The plastic turnover box is also called the PP turnover box. Its raw materials are very environmentally friendly and light, and the cost of the entire production is not high, so the selling price is also very affordable, and it can be used repeatedly, so there is more and more Many people are willing to choose plastic turnover boxes as a tool for logistics turnover.

Before it is produced, it will be precisely designed in accordance with the national production standards, and then mass-produced according to the specifications often used on the market.

From the beginning of the initial scale to the slowly developing production capacity with international standards, the production process of plastic turnover boxes has also undergone a series of changes, combined with the world’s most advanced production methods and production raw materials, plastic turnover The birth and upgrading of containers has made a huge.contribution to my country’s physical industry and logistics industry. At present, there are many companies producing plastic containers in many coastal and logistics areas of our country.

Through the above introduction, China Corrugated Plastic Container Wholesaler hopes that you can simply refer to the content of this article in future use.

Corrugated Plastic Sheet Factory Introduces Features of Corrugated Plastic Partitions:

1. Plastic hollow board has the advantages of environmental protection. It is made of PP environmentally friendly resin polypropylene and polyethylene extruded after high-temperature heating, so it is non-toxic and tasteless, and many of them are used as food storage turnover boxes.

2. The plastic hollow board is light and durable. The hollow board is so because it is plastic, so it has fewer consumables, low cost, lightweight, and easy to take.

3. Plastic hollow board has a stable chemical function. Due to the stable chemical properties of the hollow board, it has obvious chemical advantages compared with wood board and paperboard in waterproof, moisture-proof, corrosion-proof, insect-proof, and chemical resistance.

4. The plastic hollow board has excellent formability. The hollow board can be customized into various colors and sizes according to the needs of customers, and through modification, mixing, and surface spraying methods into ordinary, anti-static, and UV-resistant hollow boards, with strong variability.

5. The plastic hollow board has the effect of heat insulation and sound insulation. Due to the hollow structure of the plastic hollow board, its heat and sound transmission effect are significantly lower than that of the solid board.

6. High reusable performance. The service life of plastic hollow boards is more than 4-10 times that of corrugated cardboard. It can be recycled and gradually replaced in recent years. It is also important for hollow board materials to come. At home and abroad, more and more attention is paid to environmental protection and energy-saving, which makes domestic enterprises’ demand for hollow board boxes increase year by year. Because the anti-static hollow board box is made of PP material and anti-static material.

7. High load-bearing strength, tensile and tear resistance. The special structure of the mechanical plastic of the plastic hollow board. Therefore, it has a strong bearing capacity, resistance to tearing and not easy to break, and has excellent mechanical properties such as good toughness, impact resistance, high compressive strength, cushioning and shockproof, high stiffness, and good bending performance.

Through the above introduction, China Corrugated Plastic Container Wholesaler hopes that you can simply refer to the content of this article in future use.

Corrugated Plastic Sheet Factory Introduces Features of Corrugated Plastic Partitions :

1. Plastic hollow board has the advantages of environmental protection. It is made of PP environmentally friendly resin polypropylene and polyethylene extruded after high-temperature heating, so it is non-toxic and tasteless, and many of them are used as food storage turnover boxes.

2. The plastic hollow board is light and durable. The hollow board is so because it is plastic, so it has fewer consumables, low cost, lightweight, and easy to take.

3. Plastic hollow board has a stable chemical function. Due to the stable chemical properties of the hollow board, it has obvious chemical advantages compared with wood board and paperboard in waterproof, moisture-proof, corrosion-proof, insect-proof, and chemical resistance.

4. The plastic hollow board has excellent formability. The hollow board can be customized into various colors and sizes according to the needs of customers, and through modification, mixing, and surface spraying methods into ordinary, anti-static, and UV-resistant hollow boards, with strong variability.

5. The plastic hollow board has the effect of heat insulation and sound insulation. Due to the hollow structure of the plastic hollow board, its heat and sound transmission effect are significantly lower than that of the solid board.

6. High reusable performance. The service life of plastic hollow boards is more than 4-10 times that of corrugated cardboard. It can be recycled and gradually replaced in recent years. It is also important for hollow board materials to come. At home and abroad, more and more attention is paid to environmental protection and energy-saving, which makes domestic enterprises’ demand for hollow board boxes increase year by year. Because the anti-static hollow board box is made of PP material and anti-static material.

7. High load-bearing strength, tensile and tear resistance. The special structure of the mechanical plastic of the plastic hollow board. Therefore, it has a strong bearing capacity, resistance to tearing and not easy to break, and has excellent mechanical properties such as good toughness, impact resistance, high compressive strength, cushioning and shockproof, high stiffness, and good bending performance.

Through the above introduction, China Corrugated Plastic Case Wholesaler hopes that you can simply refer to the content of this article in future use.

https://www.yfcorrugatedplastic.com/

Corrugated Plastic Sheet Factory introduces how to maintain the hollow sheet:

1. The place where the hollow board turnover box is stored should be indoors. It is forbidden to irradiate the hollow board turnover box with sunlight for a long time, no heavy objects shall be placed on the board, no hard objects shall be placed in front of the board, and the protective film shall not be removed during storage.

2. Expired milk can be used to clean the hollow board turnover box. The content of ru acid in expired milk will increase, and ru acid is a natural detergent, which is very clean for plate cleaning.

3. Reasonably stack the goods in the plastic hollow board turnover box, do not stack them together or throw them away.

4. When using the hollow board turnover box, the user must read the text description on the protective film and use the hollow board turnover box according to the text description.

5. In normal cleaning, you should use water below 60℃, neutral detergent, and no detergent that has corrosive effect on the hollow board turnover box.

Through the above introduction, China Corrugated Plastic Container Wholesaler hopes that you can simply refer to the content of this article in future use.

As we all know, the use of hollow boards is very wide, especially in the logistics and construction industries. The performance of hollow boards can be said to be very outstanding. So today Corrugated Plastic Sheet Manufacturer will tell you about the use of hollow boards in the professional electrical industry. Right.

1. The hollow board used in the professional electrical industry needs to have three conditions. First, it needs to have good moisture-proof, flame-retardant, and anti-static functions. Secondly, it needs to have good electrical conductivity, corrosion resistance, and wear resistance. It performs well in terms of ductility and pressure resistance, and it also needs to be customized according to customer requirements. Then the hollow board used in the electrical industry is customized, in fact, you only need to find the right manufacturer and communicate your needs with the other party. There is no problem.

2. Nowadays, there are many manufacturers of hollow board customization in our country, and the boards needed by the electrical industry are quite special, so you must shop around and choose more in the market. You must not be too blind, and you must compete with those with formal qualifications and The manufacturers of advanced production equipment cooperate to ensure that the customized hollow board meets the relevant regulations.

Through the above introduction, Corrugated Plastic Container Manufacturers hopes that you can simply refer to the content of this article in future use.

As we all know, PP hollow board is a kind of non-toxic, tasteless and convenient and durable environmental protection board. Because of its own characteristics, it has the functions of rainproof, dustproof and anti-static, so it is very popular in many fields in our country. In fact, this Seed board also has another good advantage, that is, it has the function of folding. Next, Corrugated Plastic Sheet Manufacturers will teach you how to fold PP hollow sheet:

1. In fact, the folding function of the plastic hollow board is like an egg. With this function, many users can fold the finished product at will according to their own requirements and love, so why can it be folded? In fact, because this kind of board is made of HDPP, its flexibility and elasticity are very high, so it can be folded to a certain extent, especially after being made into various logistics turnover boxes. One function is fully demonstrated.

2. In real life, no matter what kind of hollow board material is used, it is only one of its advantages. For example, the decoration industry uses this kind of board because of its lightness, and the logistics industry uses this The purpose of planting the board is for it to be durable, rainproof and shockproof, and the baby carriage industry will use the hollow board as the back panel of the car.

Through the above introduction, Corrugated Plastic Container Manufacturers hopes that you can simply refer to the content of this article in future use.

With the continuous changes in the packaging market’s requirements for commodities and the development, design and application of new materials, traditional paper packaging is gradually being replaced by the market because it is not waterproof, moisture-proof, and anti-static. The emergence of PP plastic hollow boards just meets In response to this requirement of the market, the development trend has been rapid in recent years, and PP plastic hollow boards and handicrafts have already captured half of the packaging market.

Corrugated Plastic Sheet Manufacturers introduces the advantages of PP plastic hollow sheet

1. In the whole process of transportation, the mouth of the beverage bottle and the paper tray cause friction, which is very easy to cause paper shreds. The fine paper falls into the bottle, which causes environmental pollution to the beverage bottle and causes product quality problems, but the PP plastic is hollow. The board does not have this trouble.

2. The turnover frequency is low, and each paper pallet has a maximum turnover of 2-3 times, which increases the packaging cost. PP plastic hollow sheet is environmentally friendly and can be recycled to protect the environment.

3. PP plastic hollow sheet is moisture-proof, antibacterial, convenient and simple to use

Through the above introduction, Corrugated Plastic Container Manufacturers hopes that you can simply refer to the content of this article in future use.

Common features of Corrugated Plastic Sheet :


1. Environmental protection. It is made of PP environmentally friendly resin polypropylene and polyethylene extruded after high-temperature heating, so it is non-toxic and tasteless, and many of them are used as food storage turnover boxes.

2. Lightweight and durable. Because it is made of plastic, it has fewer consumables, low cost, lightweight, and easy to handle.

3. Stable chemical function. It is waterproof, moisture-proof, corrosion-proof, and insect-proof, and has obvious chemical advantages over wood and cardboard.

4. High formability. It can be customized into various colors and sizes, and through modification, mixing, and surface spraying methods into ordinary, anti-static, and anti-UV hollow boards, which are highly variable.

5. It has heat insulation and sound insulation effect. Due to the hollow structure, the heat and sound transmission effects are significantly lower than that of solid plates.

6. High reuse rate. The service life is more than 4-10 times that of corrugated cardboard, and it can be recycled.

7. High load-bearing strength, tensile and tear resistance. Due to the special structure of the corrugated plastic hollow board, it has the characteristics of good toughness, impact resistance, high compressive strength, cushioning, and shockproof.


Through the above introduction, Corrugated Plastic Container Manufacturers hopes that you can simply refer to the content of this article in future use.

Corrugated Plastic Box Supplier introduces the difference between hollow boards of different materials:

1. Plastic hollow board partition is a product made of hollow board material. It is environmentally friendly, durable, corrosion-resistant, moisture-proof, anti-static, and repeated use. It is also because of the flexibility and foldability of this board. The performance is very strong, so as long as it is used normally, it can generally be used for five to ten years. In the process of normal use, we must pay attention to the sunscreen treatment of the product. Although it is corrosion-resistant, the correct protection will prolong the use time of the board.

2. The price of the PP hollow board partition is about 5 yuan to tens of yuan. At this time, some friends will think why the price is so different. This has a lot to do with the size, thickness, and workmanship of the board. The products produced by regular manufacturers are generally of high quality, non-toxic and harmless, so the price is slightly more expensive, but it will ensure the health of the user and the later service. Also, there are some boards produced by the three-no manufacturers that are of poor quality and use There will be small problems of this or that kind.

Through the above introduction, Corrugated Plastic Partitions Manufacturers hopes that you can simply refer to the content of this article in future use.

Corrugated Plastic Sheet Manufacturer introduced that hollow board turnover boxes are only easy to use and cost-effective. They have a high reputation in my country’s transportation industry and other important fields. Anti-static hollow board is an environmentally friendly and affordable board. The use of this material to make turnover boxes of various specifications and thicknesses can not only effectively ensure the integrity of the goods inside, but also reduce the generation of unnecessary garbage. Our country has made contributions to environmental protection.

Among the many functions of the hollow board turnover box, the "anti-static" function is more interesting to many buyers, so where can I buy such products? In fact, many regions in my country have companies that produce and sell anti-static hollow board turnover boxes. The anti-static hollow board turnover boxes provided by these companies strive to be perfect in both product production and later service, so that they can survive for a long time. , So that your brand can be recognized by consumers.

In fact, as long as it has its own brand, then this company must have strong production technology and advanced production equipment, so we only need to choose among many brands according to our own needs. Only by buying products that are suitable for you, can you give full play to the effects of the products.

Through the above introduction, Corrugated Plastic Case Manufacturers hopes that you can simply refer to the content of this article in future use.

Do Corrugated Plastic Sheet Manufacturers introduce what are the advantages of foam boxes?

1. The cost of using foam boxes to grow vegetables is very low. In some markets, the price of foam boxes is generally only 1-2 yuan, which is very cheap. Therefore, the cost of using foam boxes to grow vegetables is very low.

2. The use of foam boxes to grow vegetables is very beneficial when placed because the foam boxes are very regular, and the three-dimensional way is also very beautiful, and it makes people look good.

3. Compared with the round container, this kind of foam box for planting vegetables can make more use of the balcony space because most of the balconies are square, so space can be more fully utilized when the foam box is placed.

4. It is very convenient to use the foam box when moving, but the foam box does not have drainage holes, so when using the foam box to grow vegetables, you need to leave drainage holes at the bottom.

Through the above introduction, Corrugated Plastic Container Manufacturers hope that you can simply refer to the content of this article in future use.

Corrugated Plastic Box Manufacturer Introduces PP plastic hollow board is a kind of plastic environmental protection material with multiple functions, high cost performance and long service life. In recent years, hollow board has gradually entered everyone’s field of vision with its strong moisture-proof, flame-retardant and anti-static capabilities. The frequency of use has also become higher and higher. Many fields are willing to choose PP hollow boards when processing products, especially in the express transportation industry that we are all familiar with. So, does hollow board boxes meet the requirements for packaging auto parts?

The hollow board turnover box can also be seen in the field of my country’s auto parts. In the above content, we talked about the PP hollow board turnover box, in addition to waterproof and fireproof, its anti-static ability should not be underestimated, and most of the articles in the auto parts industry are made of metal, which requires protection against static electricity in nature. At this time, the pp plastic hollow board turnover box comes in handy. It can not only prevent dust from adhering to the surface of the box, but also avoid the damage and influence of electrostatic particles on the internal fittings. It can be said to be a good product with multiple objectives.

In addition to the automobile industry, the express delivery industry transports and stores thousands of goods every day. If there is a practical and wear-resistant hollow board turnover box, then the effect of half the effort can be achieved, so the PP plastic hollow board material The logistics turnover box has become the choice of the express industry. Well, today’s content is shared here. If you need to buy pp plastic hollow board turnover box, you must go to a regular and reliable manufacturer to buy it to prevent the purchase of inferior products from affecting the subsequent use effect.


Through the above introduction, Corrugated Plastic Partitions Manufacturers hopes that you can simply refer to the content of this article in future use.

Corrugated Plastic Sheet Manufacturers introduces the difference between plastic hollow board and wood board:

Due to the hollow structure of the plastic hollow board, its heat and sound transmission effect is significantly lower than that of the solid board, and it has good heat insulation and sound insulation effects. Modification, mixing, surface spraying and other methods can make the plastic hollow board have antistatic, conductive, or flame retardant properties.

Plastic hollow board can be waterproof, moisture-proof, anti-corrosion, insect-proof, and fumigation-free. Compared with cardboard and wood board, it has obvious advantages. Due to the special molding process of the plastic hollow board, any color can be achieved through the toning of the masterbatch, and the surface is smooth and easy to print. The special structure of the plastic hollow board makes it have excellent mechanical properties such as good toughness, impact resistance, high compressive strength, cushioning and shockproof, high stiffness, and good bending performance. The plastic hollow board has excellent mechanical properties, and the same effect should be achieved year-on-year. The use of plastic hollow board has less consumables, low cost and light weight.

Through the above introduction, Corrugated Plastic Case Manufacturers hopes that you can simply refer to the content of this article in future use.